# Are these Xbee connections correct?

**URL:** <https://forums.digi.com/t/are-these-xbee-connections-correct/13921>\
**Category:** XCTU\
**Tags:** at, analog-input, xctu, xbee\
**Created:** [November 13, 2014, 10:53pm UTC](https://forums.digi.com/t/are-these-xbee-connections-correct/13921 "2014-11-13T22:53:20Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Rod1](https://avatars.discourse-cdn.com/v4/letter/r/dec6dc/32.png) [@Rod1](https://forums.digi.com/u/Rod1)\
**Post date:** [November 13, 2014, 10:53pm UTC](https://forums.digi.com/t/are-these-xbee-connections-correct/13921/1 "2014-11-13T22:53:20Z")

</div>

I have the system assembled and am using XCTU, but I need help.

The receiver is an Xbee connected to an Explorer.  
The transmitter is an Xbee plugged into a Shield which is plugged into a Redboard.  
The Redboard has a 9v battery plugged into the round socket.  
There are two analog sensors connected to the Shield.  
Both sensors are connected to +5v and GND.  
The output from the sensors are connected to Analog In 0 and 1.  
Is this wiring correct?

D0 and D1 are both set to analog (2) on transmitter and receiver.  
AP is set to 0 on transmitter and receiver.

When I run XCTU in AT mode, commands like ATID and ATD0 work fine.  
AT%V returns ERROR.  
Why do I get an error?

ATIS returns:  
1  
600  
3FF  
3FF  
Does this tell you anything?

Thanks.

Rod

---

<div class="post-metadata">

**Author:** ![mvut](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.digi.com/mvut/32/31_2.png) [@mvut](https://forums.digi.com/u/mvut)\
**Post date:** [November 14, 2014, 8:24am UTC](https://forums.digi.com/t/are-these-xbee-connections-correct/13921/2 "2014-11-14T08:24:40Z")

</div>

Which XBee modules are you using? What is the min and max output voltages of the sensor?

---

<div class="post-metadata">

**Author:** ![Rod1](https://avatars.discourse-cdn.com/v4/letter/r/dec6dc/32.png) [@Rod1](https://forums.digi.com/u/Rod1)\
**Post date:** [November 14, 2014, 1:34pm UTC](https://forums.digi.com/t/are-these-xbee-connections-correct/13921/3 "2014-11-14T13:34:44Z")

</div>

I am using Xbee Series 1 (802.15.4). The min and max output voltages are 0 to 1v.

---

<div class="post-metadata">

**Author:** ![mvut](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.digi.com/mvut/32/31_2.png) [@mvut](https://forums.digi.com/u/mvut)\
**Post date:** [November 19, 2014, 9:58am UTC](https://forums.digi.com/t/are-these-xbee-connections-correct/13921/4 "2014-11-19T09:58:52Z")

</div>

You need to connect VREF to your max output voltage. I would also suggest reading over [http://www.digi.com/support/kbase/kbaseresultdetl?id=2180](http://www.digi.com/support/kbase/kbaseresultdetl?id=2180)
