# Digi Passport Console Server Raw TCP mode

**URL:** <https://forums.digi.com/t/digi-passport-console-server-raw-tcp-mode/6521>\
**Category:** Digi CM & Passport\
**Created:** [May 19, 2011, 9:03am UTC](https://forums.digi.com/t/digi-passport-console-server-raw-tcp-mode/6521 "2011-05-19T09:03:04Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![ldubost](https://avatars.discourse-cdn.com/v4/letter/l/e99b99/32.png) [@ldubost](https://forums.digi.com/u/ldubost)\
**Post date:** [May 19, 2011, 9:03am UTC](https://forums.digi.com/t/digi-passport-console-server-raw-tcp-mode/6521/1 "2011-05-19T09:03:04Z")

</div>

Hello,  
I am using a Passport as a “normal” port server with a SCADA on one side and serial device connected behind the Passport.  
I have configure my port as a console port, I access in raw TCP.  
I need a really “transparent” conversion from TCP/IP to serial.

The Digi sends me some ASCII messages like:  
“Welcome to Digi Passport …”  
“Port is in use. Closing connection …”  
“\>\> ‘nobody’ initiated a new r/W session …”

These messages are read by my driver on SCADA side … and I really want to suppress them.

Do you have an idea ?

Regards?

---

<div class="post-metadata">

**Author:** ![Ron](https://avatars.discourse-cdn.com/v4/letter/r/ecae2f/32.png) [@Ron](https://forums.digi.com/u/Ron)\
**Post date:** [May 19, 2011, 1:48pm UTC](https://forums.digi.com/t/digi-passport-console-server-raw-tcp-mode/6521/2 "2011-05-19T13:48:49Z")

</div>

You need to set these options to remove those msgs:

Serial port-\>Config-\>“#”-\>Host mode conf-\>Display port info=Disable

Serial port-\>Config-\>“#”-\>User access ctrl-\>suppress conn announce=Enable

---

<div class="post-metadata">

**Author:** ![ldubost](https://avatars.discourse-cdn.com/v4/letter/l/e99b99/32.png) [@ldubost](https://forums.digi.com/u/ldubost)\
**Post date:** [May 20, 2011, 11:05am UTC](https://forums.digi.com/t/digi-passport-console-server-raw-tcp-mode/6521/3 "2011-05-20T11:05:57Z")

</div>

Thanks for your help,

I cannot find the 2nd option “suppress conn announce” !!!

In host mode menu I have:

1. Host mode : Console server
2. Type of console server : Other
3. Rackable System Management Card : Disable
4. Service processor : NONE
5. Enable/Disable assigned IP address : Disable
6. Listening TCP port : 2106
7. Protocol : RawTCP
8. Inactivity timeout : 100 second(s)  
9. Display port information : Disable
9. Port escape sequence option : Disable
10. Port break sequence : ~break
11. Use comment : No
12. Quick connect via : Web applet
13. Web applet encoding : English (latin1)
14. Web applet size : 80 / 24

And in User Access Control :

1. User Permissions
2. Enable/Disable multiple session : Disable

I have upgrade my digi to the last release 1.3.0.2 … but nothing change.

Regards

---

<div class="post-metadata">

**Author:** ![Ron](https://avatars.discourse-cdn.com/v4/letter/r/ecae2f/32.png) [@Ron](https://forums.digi.com/u/Ron)\
**Post date:** [May 20, 2011, 3:18pm UTC](https://forums.digi.com/t/digi-passport-console-server-raw-tcp-mode/6521/4 "2011-05-20T15:18:36Z")

</div>

Sorry, the “Suppress …” option is only in the 1.4.x beta. Unfortunately you will need it.

Auth=None and Display port=Disable will suppress initial messages but it does not disable:  
“\>\> ‘nobody’ initiated a new r/W session …”  
This requires the “Suppress …” option.

Please refer to your support case for further info regarding the beta.