# Download problem

**URL:** <https://forums.digi.com/t/download-problem/4522>\
**Category:** NET+OS\
**Created:** [January 29, 2004, 1:55pm UTC](https://forums.digi.com/t/download-problem/4522 "2004-01-29T13:55:44Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![system](https://us1.discourse-cdn.com/flex016/uploads/digi/original/1X/11da31a6a1fbcd03ef21d3f785c317c824009ae2.png) [@system](https://forums.digi.com/u/system)\
**Post date:** [January 29, 2004, 1:55pm UTC](https://forums.digi.com/t/download-problem/4522/1 "2004-01-29T13:55:44Z")

</div>

Hello,I have developed a program and debugged it on a development board from Netsilicon using the Raven ICE. Now I try to load the debug version on a new application card in RAM, but it will not, see printout below. The RAM has the same base address 0x200 0000 on both cards, but the new card has only 2 Mb, not 16 MB. My program is about 300 kb big. Is this a software or hardware error? \*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\* Playing back from S:\GHS\arm35\defaults\os\_aware xarm.rc Connected to target `ocdserv rlpt1 arm7t -big -nobss -setup S:\NETOS5\_GH35  
et5032b.ocd’. Downloading program text and data. Please Wait… ocdserv: A remote target memory check failed in the .text program segment. ocdserv: This is usually caused by failure to set the board up properly, but can ocdserv: also be caused by a bad link map or by a program that is bigger than ocdserv: available board memory. Make sure the board setup procedure completed ocdserv: without errors, as this is the most common cause of this problem. Download failed, error during write 0x1000 - 0x1047 debug server: download of “S:\NETOS5\_GH35\src\apps\IPM\32b\debug” failed Couldn’t load program. MULTI\> \*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\*\* Best regards Henric Rappe

---

<div class="post-metadata">

**Author:** ![system](https://us1.discourse-cdn.com/flex016/uploads/digi/original/1X/11da31a6a1fbcd03ef21d3f785c317c824009ae2.png) [@system](https://forums.digi.com/u/system)\
**Post date:** [January 29, 2004, 2:59pm UTC](https://forums.digi.com/t/download-problem/4522/2 "2004-01-29T14:59:42Z")

</div>

Hi again, Correction: I did say the wrong RAM address, it is 0x0 on both cards. The address 0x200 0000 is for the flash area on both cards. Henric Rappe

---

<div class="post-metadata">

**Author:** ![system](https://us1.discourse-cdn.com/flex016/uploads/digi/original/1X/11da31a6a1fbcd03ef21d3f785c317c824009ae2.png) [@system](https://forums.digi.com/u/system)\
**Post date:** [January 30, 2004, 9:50am UTC](https://forums.digi.com/t/download-problem/4522/3 "2004-01-30T09:50:30Z")

</div>

Hi,We have found the problem. The reset did not work properly, so the Chip Select settings were not made, and then nothing else. After a small fix on the reset the download and running did work fine. Henric Rappe
