# How to link a INNR smart lamp to a XBEE S2C coordinator **URL:** \ **Category:** XBee - 802.15.4\ **Tags:** device, home, automation, end, joining\ **Created:** [September 6, 2017, 9:56am UTC](https://forums.digi.com/t/how-to-link-a-innr-smart-lamp-to-a-xbee-s2c-coordinator/18694 "2017-09-06T09:56:11Z")\ **Posts on this page:** 4\ **Page:** 1
**Author:** ![koen\_algoet](https://avatars.discourse-cdn.com/v4/letter/k/5e9695/32.png) [@koen\_algoet](https://forums.digi.com/u/koen_algoet)\ **Post date:** [September 6, 2017, 9:56am UTC](https://forums.digi.com/t/how-to-link-a-innr-smart-lamp-to-a-xbee-s2c-coordinator/18694/1 "2017-09-06T09:56:11Z")
I have 2 XBEE S2C. One as coordinator , the other as router. Firmware version : 405F My XBEE’s are plugged into a groove dev board. I’m playing with XCTU and some com port logging tool. I’m testing now one RB innr 175 W smart lamp. (which should work with philips Hue and Osram Lighify) With my 2 boards I can do remote AT commands to control leds on the groove board and so on. That seams to be working. Now I’m trying to have a smart device (innr lamp) connected so I can control the lamp by sending commands. In the XCTU when I do a ‘scan’ I see the end device but it seems it does not join. I see Max address:00158D00017C529F, netw addr5381, type router and ‘unknown ?LQI’ If I click on the device in the scan window from the XCTU I get a message ‘…device sleeping or not in the network any more’ I did enable the encryption EE=1,EO=1 KY=5A6967… So here I’m lost… - should the joining of the lamp with the coordinator by done 100% auto without need of serial commands via the XCTU? The beacon/association process. - Can I should I see beacon communication on my serial? Or is this handled at lower layer. - I was trying to setup my second Xbee as transparent to see if I could sniff beacon packages but no success. Thanks if someone could point me in the right direction! I’m new to this so still learning. Koen Algoet Belgium ---
**Author:** ![mvut](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.digi.com/mvut/32/31_2.png) [@mvut](https://forums.digi.com/u/mvut)\ **Post date:** [September 6, 2017, 10:31am UTC](https://forums.digi.com/t/how-to-link-a-innr-smart-lamp-to-a-xbee-s2c-coordinator/18694/2 "2017-09-06T10:31:24Z")
No, not on this device. This device requires you to do some ZDO commands to Pair the device during the association process otherwise it will remove its self from the network. ---
**Author:** ![koen\_algoet](https://avatars.discourse-cdn.com/v4/letter/k/5e9695/32.png) [@koen\_algoet](https://forums.digi.com/u/koen_algoet)\ **Post date:** [September 6, 2017, 11:08am UTC](https://forums.digi.com/t/how-to-link-a-innr-smart-lamp-to-a-xbee-s2c-coordinator/18694/3 "2017-09-06T11:08:11Z")
I was hoping that I could receive the assosiation communication on the serial port which is connected to my pc and could send the ZDO commands via an testing program. I use XCTU to test and also a test program in visual studio. But I do not see this beacon request nor association request on the serial port. I did set DC10 (verbose) but still nothing on the serial port. ---
**Author:** ![mvut](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.digi.com/mvut/32/31_2.png) [@mvut](https://forums.digi.com/u/mvut)\ **Post date:** [September 6, 2017, 11:14am UTC](https://forums.digi.com/t/how-to-link-a-innr-smart-lamp-to-a-xbee-s2c-coordinator/18694/4 "2017-09-06T11:14:03Z")
Did you set the XBee module for API mode and for ZDO pass thru?