# Once I have hooked up a Digi Connect Wi-SP to my PC using Hyper Terminal, how do I associate the Wi-SP to my home WiFi?

**URL:** <https://forums.digi.com/t/once-i-have-hooked-up-a-digi-connect-wi-sp-to-my-pc-using-hyper-terminal-how-do-i-associate-the-wi-sp-to-my-home-wifi/13739>\
**Category:** XBee & XBee Gateway\
**Tags:** connect, wi-sp, digi\
**Created:** [October 13, 2014, 4:32pm UTC](https://forums.digi.com/t/once-i-have-hooked-up-a-digi-connect-wi-sp-to-my-pc-using-hyper-terminal-how-do-i-associate-the-wi-sp-to-my-home-wifi/13739 "2014-10-13T16:32:56Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![Fernando\_Borja](https://avatars.discourse-cdn.com/v4/letter/f/45deac/32.png) [@Fernando\_Borja](https://forums.digi.com/u/Fernando_Borja)\
**Post date:** [October 13, 2014, 4:32pm UTC](https://forums.digi.com/t/once-i-have-hooked-up-a-digi-connect-wi-sp-to-my-pc-using-hyper-terminal-how-do-i-associate-the-wi-sp-to-my-home-wifi/13739/1 "2014-10-13T16:32:56Z")

</div>

I used to set up my Digi Connect Wi-SP for Ad-Hoc networks but with the latest firmware I know it is not possible any more, so what is the procedure to hook up the Wi-SP to any WiFi access point?  
I have hooked up the Wi-SP using a serial cable to my PC with Hyper Terminal, so I can read the default configuration.

---

<div class="post-metadata">

**Author:** ![halovapor](https://avatars.discourse-cdn.com/v4/letter/h/54ee81/32.png) [@halovapor](https://forums.digi.com/u/halovapor)\
**Post date:** [October 13, 2014, 4:34pm UTC](https://forums.digi.com/t/once-i-have-hooked-up-a-digi-connect-wi-sp-to-my-pc-using-hyper-terminal-how-do-i-associate-the-wi-sp-to-my-home-wifi/13739/2 "2014-10-13T16:34:00Z")

</div>

Here is a knowledge base on the Digi Support site that may be helpful

[http://www.digi.com/support/kbase/kbaseresultdetl?id=963](http://www.digi.com/support/kbase/kbaseresultdetl?id=963)

---

<div class="post-metadata">

**Author:** ![Fernando\_Borja](https://avatars.discourse-cdn.com/v4/letter/f/45deac/32.png) [@Fernando\_Borja](https://forums.digi.com/u/Fernando_Borja)\
**Post date:** [October 14, 2014, 1:12am UTC](https://forums.digi.com/t/once-i-have-hooked-up-a-digi-connect-wi-sp-to-my-pc-using-hyper-terminal-how-do-i-associate-the-wi-sp-to-my-home-wifi/13739/3 "2014-10-14T01:12:37Z")

</div>

Thank you for your quick answer.  
I reset the Wi-SP, this is what I get with a “disp wlan”:  
State: scanning  
Channel: 0  
SSID: ?  
BSSID: 00:00:00:00:00:00  
tx rate: 0 Mbps  
rx signal strength: 45% (-63dBm)  
authentication: open system  
encryption: open system  
I tried to assign a SSID to the Wi-SP (set trace SSID Connect). This is not working as I expected because of the new firmware with no ad hoc network possibility.  
Being impossible to set up the SSID, how the Wi-SP is going to associate with the WAP?