# RCM5700 Adding RJ45 Jack

**URL:** <https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313>\
**Category:** Rabbit\
**Created:** [October 25, 2008, 2:19pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313 "2008-10-25T14:19:45Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![seulater](https://avatars.discourse-cdn.com/v4/letter/s/54ee81/32.png) [@seulater](https://forums.digi.com/u/seulater)\
**Post date:** [October 25, 2008, 2:19pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/1 "2008-10-25T14:19:45Z")

</div>

The RCM5700 comes without a RJ45 jack mounted on the board. Does Rabbit plan on making a RCM5700 available with the RJ45 jack ?

And if not, what’s involved in placing one on the module.

---

<div class="post-metadata">

**Author:** ![chuckphd53](https://avatars.discourse-cdn.com/v4/letter/c/df705f/32.png) [@chuckphd53](https://forums.digi.com/u/chuckphd53)\
**Post date:** [November 6, 2008, 5:01pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/2 "2008-11-06T17:01:57Z")

</div>

I’ve looked at this and determined  
that you would need to add many  
additional parts after you added  
the RJ45 jack…

These are 603 and 402 size parts…  
not for the novice…

best to interface your RCM5700 to  
your board design. I did this and bought  
the 10-Base-T from the rabbit store  
PN 530-0023, had NO luck instead I used  
a FIL-MAG PN 23Z467SM part, Mouser Electronics  
has these and it worked great…

Keep in mind that if you lay out your  
PCB to make sure you have NO Ground or Power Plane  
under the Transformer and it’s associated parts…

Look at the Rabbit RCM5700 schematic and try to use  
the same interface parts to the Transformer  
as they did on the schem.

---

<div class="post-metadata">

**Author:** ![seulater](https://avatars.discourse-cdn.com/v4/letter/s/54ee81/32.png) [@seulater](https://forums.digi.com/u/seulater)\
**Post date:** [November 6, 2008, 5:03pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/3 "2008-11-06T17:03:59Z")

</div>

I have been informed by Rabbit that they will have a version of this with the RJ45 and suported parts soon.

---

<div class="post-metadata">

**Author:** ![VNee](https://avatars.discourse-cdn.com/v4/letter/v/2bfe46/32.png) [@VNee](https://forums.digi.com/u/VNee)\
**Post date:** [November 27, 2008, 12:01am UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/4 "2008-11-27T00:01:47Z")

</div>

For what it’s worth, I can’t wait to get  
the RCM5700 with on-board RJ45.  
I have a project that calls just for  
this so, let’s hope that the RJ45  
flavor sees the light of day soon.

I’m ordering the additional components  
soon and will retrofit my unit with the jack  
from the development board.

Yeah, I know - 0402 packages and  
warranty void (but hey, I also have  
pillows with no “DO-NOT-REMOVE” labels!)

B.Robert

---

<div class="post-metadata">

**Author:** ![seulater](https://avatars.discourse-cdn.com/v4/letter/s/54ee81/32.png) [@seulater](https://forums.digi.com/u/seulater)\
**Post date:** [November 27, 2008, 10:10pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/5 "2008-11-27T22:10:38Z")

</div>

lets just hope they dont jack the cost way up to add a few popcorn components and the jack.

---

<div class="post-metadata">

**Author:** ![Nicola](https://avatars.discourse-cdn.com/v4/letter/n/41988e/32.png) [@Nicola](https://forums.digi.com/u/Nicola)\
**Post date:** [January 19, 2009, 5:16pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/6 "2009-01-19T17:16:20Z")

</div>

Are there some news about the module RCM5700 with the RJ45 connector on?

I developed a board for the module but I am not able to communicate with the module. In particular it seems that the module receive (if I ping the module I saw the ACT LED blinking) but it is not able to transmit.

Some advise?

---

<div class="post-metadata">

**Author:** ![chuckphd53](https://avatars.discourse-cdn.com/v4/letter/c/df705f/32.png) [@chuckphd53](https://forums.digi.com/u/chuckphd53)\
**Post date:** [January 19, 2009, 5:28pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/7 "2009-01-19T17:28:45Z")

</div>

Nicola…

you didn’t mention how your design was implemented…  
I assume you have a ethernet Txfrm as part of your  
interface…

can you give some details on the board design…

Chuck

---

<div class="post-metadata">

**Author:** ![Nicola](https://avatars.discourse-cdn.com/v4/letter/n/41988e/32.png) [@Nicola](https://forums.digi.com/u/Nicola)\
**Post date:** [January 19, 2009, 5:38pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/8 "2009-01-19T17:38:41Z")

</div>

That’s right. I’m sorry for the cross-post. Here: [http://www.rabbit.com/forums/showthread.php?t=1358](http://www.rabbit.com/forums/showthread.php?t=1358) you can find part of my electrical scheme. I use a RJ45 connector with the transformer in.  
The connector is for 10/100Mbit Tbase interface.

Thank you for the support.

---

<div class="post-metadata">

**Author:** ![chuckphd53](https://avatars.discourse-cdn.com/v4/letter/c/df705f/32.png) [@chuckphd53](https://forums.digi.com/u/chuckphd53)\
**Post date:** [January 19, 2009, 5:45pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/9 "2009-01-19T17:45:45Z")

</div>

Nicola…

Could not tell too much form your schem…

BUT…be sure that the RJ45 connector is not placed on  
the PCB with GOUND or POWER Planes below it…

this should be just bare PCB to avoid any coupling of noise/signals  
and suppression of the signals…

One thing you can try…is to remove the RJ45 connector and place  
it on 1/2 inch of wire to stand OFF the PCB .

It will look like a spider sitting tall…but this will remove any coupling  
to the pcb and then try your software pinging again…

I have done this with success…on prototypes…

chuck

---

<div class="post-metadata">

**Author:** ![Nicola](https://avatars.discourse-cdn.com/v4/letter/n/41988e/32.png) [@Nicola](https://forums.digi.com/u/Nicola)\
**Post date:** [January 19, 2009, 6:00pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/10 "2009-01-19T18:00:04Z")

</div>

Chuck,

thank you very much for your advise. On my pcb I have ground plane under the RJ45 connector!! Tomorrow I will try to wire my connector and then I will tell you the result.

Thank you again.

Nicola

---

<div class="post-metadata">

**Author:** ![Nicola](https://avatars.discourse-cdn.com/v4/letter/n/41988e/32.png) [@Nicola](https://forums.digi.com/u/Nicola)\
**Post date:** [January 20, 2009, 10:15am UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/11 "2009-01-20T10:15:29Z")

</div>

I tested my board with the connector placed about 1 cm above the pcb but nothing has chnaged.  
The first test consist in placing the RJ45 connector above the pcb (using wrap wire) and without the filter on board. The result is: I saw LINK LED green and ACT LED blinking (the frequency of the blink change if I change the ping frequency).  
I placed the filter (i.e. the L, the C and the 2R for TX and for RX) and in this case the ACT and LINK LEDs are off.

---

<div class="post-metadata">

**Author:** ![chuckphd53](https://avatars.discourse-cdn.com/v4/letter/c/df705f/32.png) [@chuckphd53](https://forums.digi.com/u/chuckphd53)\
**Post date:** [January 20, 2009, 2:00pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/12 "2009-01-20T14:00:52Z")

</div>

Not sure that 1cm will be enought 2cm is better…

I believe the RJ45 jack you are using has the filters  
built in…(not sure) you may want to take the wires  
direct from the processor to the RJ45 jack and try that…

also…I believe there is a PING sample program, use this  
to test with to eliminate any possiblity of software issues…

Let us know…

chuck

ps…you are using a HUB between the two computers  
or an ethernet xover cable from computer to rabbit…

---

<div class="post-metadata">

**Author:** ![Nicola](https://avatars.discourse-cdn.com/v4/letter/n/41988e/32.png) [@Nicola](https://forums.digi.com/u/Nicola)\
**Post date:** [January 20, 2009, 2:38pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/13 "2009-01-20T14:38:36Z")

</div>

There is something strange…

I place my ethernet connector with magnetic on the RCM5700 module; after that I close the R (0 ohm) on the module. I did not place the filter (C, L and 2R) on the module!!

If I place the module on the development board and connect the Ethernet cable in the connector placed on the module all works.

If I place the module on my board and connect the ethernet cable the system does not work! I cut the ethernet net on my board ner the miniPCI connector: nothing!

---

<div class="post-metadata">

**Author:** ![chuckphd53](https://avatars.discourse-cdn.com/v4/letter/c/df705f/32.png) [@chuckphd53](https://forums.digi.com/u/chuckphd53)\
**Post date:** [January 20, 2009, 2:51pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/14 "2009-01-20T14:51:41Z")

</div>

INTERESTING !!!

I guess the only thing I can think of is, make sure  
that your TX+ TX- RX+ RX- lines are correct…

I’ve attached a simple interface that I have used  
and it works, make sure your lines are the same.

Chuck

Also…notice on the Rabbit test board that the edge of the 5700  
module is directly on the edge of the test board…

On ‘your’ board, is the RCM5700 located in the center near anything ??  
also…ck your power 3.3V.

What other items do you have on ‘your’ design board ??

---

<div class="post-metadata">

**Author:** ![Nicola](https://avatars.discourse-cdn.com/v4/letter/n/41988e/32.png) [@Nicola](https://forums.digi.com/u/Nicola)\
**Post date:** [January 20, 2009, 3:20pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/15 "2009-01-20T15:20:22Z")

</div>

The interface pins are connected in the right way.  
I attached the TOP layer of my board, in red I highlight the TX+ TX- RX+ and RX- net.  
What do you think about the layout?

The RCM5700 on my system manage an I2C bus and a serial port. All works well… except the ethernet.

---

<div class="post-metadata">

**Author:** ![chuckphd53](https://avatars.discourse-cdn.com/v4/letter/c/df705f/32.png) [@chuckphd53](https://forums.digi.com/u/chuckphd53)\
**Post date:** [January 20, 2009, 3:41pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/16 "2009-01-20T15:41:27Z")

</div>

The board looks fine…

The only thing I see that bothers me is the  
traces under the RJ45 conn… (see my attached)

Did you try only connecting the TX/RX pins to the  
RJ45 conn and nothing else ? (with the RJ45 ‘OFF’ the board )

so you only have the RCM5700 lines to the RJ45 conn  
and forget the LED’s. Trying to eliminate possible problems.

also…try NOT connecting the RJ45 case to ground…  
let it float.

---

<div class="post-metadata">

**Author:** ![Nicola](https://avatars.discourse-cdn.com/v4/letter/n/41988e/32.png) [@Nicola](https://forums.digi.com/u/Nicola)\
**Post date:** [January 20, 2009, 4:04pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/17 "2009-01-20T16:04:08Z")

</div>

Now I am concentrating on the on the module. I placed the RJ connector on the module and connect it to the Ethernet.  
If the module is placed on the development board the communication work, if the module is on my system the communication does not work.

The module is powered in the correct way (I use a LDO with 3.3V and 1000mA in output). Nothing else should interest the ethernet communication, right?

---

<div class="post-metadata">

**Author:** ![chuckphd53](https://avatars.discourse-cdn.com/v4/letter/c/df705f/32.png) [@chuckphd53](https://forums.digi.com/u/chuckphd53)\
**Post date:** [January 20, 2009, 4:24pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/18 "2009-01-20T16:24:23Z")

</div>

You are correct…

You have cut the ethernet traces at the RCM5700 miniPCI on  
your board…this should eliminate any noise or loading…

Power 3.3 LDO looks fine…

I guess I am out of suggestions…

I believe you have done everything right…

There must be some difference between your board and the  
Rabbit test board…review both schematics and look for differences  
and let me know if you find something…

look for any terminations on the test board / pull ups etc…

sorry I could not help more…good luck and please let me know  
what you find…

chuck

---

<div class="post-metadata">

**Author:** ![Nicola](https://avatars.discourse-cdn.com/v4/letter/n/41988e/32.png) [@Nicola](https://forums.digi.com/u/Nicola)\
**Post date:** [January 20, 2009, 4:33pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/19 "2009-01-20T16:33:40Z")

</div>

Update: I try to power the RCM5700 module with the RJ on board directly (I place 2 wire on the power supply pins). The result is the same that I have using my board.

---

<div class="post-metadata">

**Author:** ![chuckphd53](https://avatars.discourse-cdn.com/v4/letter/c/df705f/32.png) [@chuckphd53](https://forums.digi.com/u/chuckphd53)\
**Post date:** [January 21, 2009, 2:11pm UTC](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313/20 "2009-01-21T14:11:25Z")

</div>

This would suggest that something is different when you plug it into the  
test board…

Check the Schems of the test board and see if you can find any  
differences…

Q: Did you isolate all four lines Tx+,Tx-,Rx+,Rx- on the RCM module  
by cutting the traces on the edge connector ??

OR:

Do the signal go to both your RJ45 conn and the Test board RJ45 conn ??

[Next page](https://forums.digi.com/t/rcm5700-adding-rj45-jack/9313.md?page=2)
