# remote AT command no response

**URL:** <https://forums.digi.com/t/remote-at-command-no-response/1471>\
**Category:** XBee - 802.15.4\
**Created:** [February 23, 2010, 10:03am UTC](https://forums.digi.com/t/remote-at-command-no-response/1471 "2010-02-23T10:03:02Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![andrewang](https://avatars.discourse-cdn.com/v4/letter/a/a9a28c/32.png) [@andrewang](https://forums.digi.com/u/andrewang)\
**Post date:** [February 23, 2010, 10:03am UTC](https://forums.digi.com/t/remote-at-command-no-response/1471/1 "2010-02-23T10:03:02Z")

</div>

Hi all,

I tried to follow the XBee manual (page 60 of version printed on 2009.09.23) to request the DL numbers of a remote node but has no luck. The packet I sent is:

7E 00 0F 17 52 00 13 A2 00 40 3B 59 2C FF FE 02 44 4C AD

There is no response at all.

The settings are:

1. Firmware: both are 10e6.

2. Configurations: remote node - end device, local node - coordinator.

3. API: both enabled, local API commands are OK on both nodes.

4. Transparent communication: Tried continuous sending of data, no problem.

5. Local AT command: no proble on both nodes.

6. Remote node (end device) addresses:  
PANID: 3332.  
DL: 1112.  
MY: 1A00.  
SH: 13A200.  
SL: 403B592C.

7. Local node (coordinator) addresses:  
PANID: 3332.  
DL: 1A00.  
MY: 1112.  
SH: 13A200.  
SL: 403B592D.

8. Packet sending device: X-CTU, packet is wriiten in “send packet” window in HEX format. Communications were performed in “Terminal” tab.

Any other settings should I do/amend or should I change the packet?  
Many thanks in advance.

Andrew

---

<div class="post-metadata">

**Author:** ![andrewang](https://avatars.discourse-cdn.com/v4/letter/a/a9a28c/32.png) [@andrewang](https://forums.digi.com/u/andrewang)\
**Post date:** [February 23, 2010, 11:26am UTC](https://forums.digi.com/t/remote-at-command-no-response/1471/2 "2010-02-23T11:26:21Z")

</div>

Hi all,

Please ignore my question, i get the checksum wrong, forgot to subtract the figure from 0xFF.

Sorry.

Andrew

---

<div class="post-metadata">

**Author:** ![16ksa23](https://avatars.discourse-cdn.com/v4/letter/1/aeb1de/32.png) [@16ksa23](https://forums.digi.com/u/16ksa23)\
**Post date:** [September 22, 2014, 1:23am UTC](https://forums.digi.com/t/remote-at-command-no-response/1471/3 "2014-09-22T01:23:27Z")

</div>

You can easily form the frames using the Digi API maker which can be found at the following link, [http://ftp1.digi.com/support/utilities/digi\_apiframes2.htm](http://ftp1.digi.com/support/utilities/digi_apiframes2.htm)