# Where is xbee3 output for analog sensor on XCTU serial console?

**URL:** <https://forums.digi.com/t/where-is-xbee3-output-for-analog-sensor-on-xctu-serial-console/22162>\
**Category:** XBee - 802.15.4\
**Tags:** xbee3\
**Created:** [January 26, 2021, 12:35pm UTC](https://forums.digi.com/t/where-is-xbee3-output-for-analog-sensor-on-xctu-serial-console/22162 "2021-01-26T12:35:57Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Rod1](https://avatars.discourse-cdn.com/v4/letter/r/dec6dc/32.png) [@Rod1](https://forums.digi.com/u/Rod1)\
**Post date:** [January 26, 2021, 12:35pm UTC](https://forums.digi.com/t/where-is-xbee3-output-for-analog-sensor-on-xctu-serial-console/22162/1 "2021-01-26T12:35:57Z")

</div>

Transmitter is an xbee3 on a shield and redboard.  
Receiver is an xbee3 on an explorer.  
Analog pressure sensor is connected to +5v, gnd, and analog input 0 on shield.  
With a voltmeter, baseline sensor output is .18v.  
Using XCTU serial console, output is 1.09v from the following commands:  
+++OK  
ATD02  
OK  
ATAC  
OK  
ATIS  
01  
0600  
03FF  
03A1  
Is 03A1 the output for analog 0?  
03A1 is 929 bits or 929\*(1.2/1023) = 1.09v?  
What is wrong?  
Any help would be appreciated.

---

<div class="post-metadata">

**Author:** ![mvut](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.digi.com/mvut/32/31_2.png) [@mvut](https://forums.digi.com/u/mvut)\
**Post date:** [January 26, 2021, 1:21pm UTC](https://forums.digi.com/t/where-is-xbee3-output-for-analog-sensor-on-xctu-serial-console/22162/2 "2021-01-26T13:21:42Z")

</div>

The analog inputs of the XBee 3 are not 5V. They are either 1.25 or 2.5V based off of the AV command. That means that your sensor needs to be either 1.25 or 2.5V output or the proper level shifters.

---

<div class="post-metadata">

**Author:** ![Rod1](https://avatars.discourse-cdn.com/v4/letter/r/dec6dc/32.png) [@Rod1](https://forums.digi.com/u/Rod1)\
**Post date:** [January 27, 2021, 9:01am UTC](https://forums.digi.com/t/where-is-xbee3-output-for-analog-sensor-on-xctu-serial-console/22162/3 "2021-01-27T09:01:11Z")

</div>

The sensor output is 0 to 5v but my application only uses 0 to 1v. Does that make a difference?

---

<div class="post-metadata">

**Author:** ![mvut](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.digi.com/mvut/32/31_2.png) [@mvut](https://forums.digi.com/u/mvut)\
**Post date:** [January 29, 2021, 10:09am UTC](https://forums.digi.com/t/where-is-xbee3-output-for-analog-sensor-on-xctu-serial-console/22162/4 "2021-01-29T10:09:22Z")

</div>

Yes it does. The sensor is still 0 - 5V. So you must use a level shifter to connect its analog 0 - 5V output to the XBee modules ADC line as it is still only going to support a 0 - 1.25 or 0 - 2.5V.
