# Why do pings time out from devices connected to my WR21

**URL:** <https://forums.digi.com/t/why-do-pings-time-out-from-devices-connected-to-my-wr21/13971>\
**Category:** Digi TransPort WR (Series)\
**Tags:** transport\
**Created:** [November 21, 2014, 8:21am UTC](https://forums.digi.com/t/why-do-pings-time-out-from-devices-connected-to-my-wr21/13971 "2014-11-21T08:21:00Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![joe.vance](https://avatars.discourse-cdn.com/v4/letter/j/67e7ee/32.png) [@joe.vance](https://forums.digi.com/u/joe.vance)\
**Post date:** [November 21, 2014, 8:21am UTC](https://forums.digi.com/t/why-do-pings-time-out-from-devices-connected-to-my-wr21/13971/1 "2014-11-21T08:21:00Z")

</div>

I’m using the firewall, with an almost default configuration. I’ve added 2 forwarding rules, as well as a rule to allow incoming icmp. I’m also using the DHCP server, with a static address reservation. I’m able to connect inbound to my device with no issues, but outgoing ping requests don’t get a response, and my device acts as though it has no outgoing internet connection.

---

<div class="post-metadata">

**Author:** ![NicholasWilson](https://avatars.discourse-cdn.com/v4/letter/n/c77e96/32.png) [@NicholasWilson](https://forums.digi.com/u/NicholasWilson)\
**Post date:** [November 21, 2014, 8:42am UTC](https://forums.digi.com/t/why-do-pings-time-out-from-devices-connected-to-my-wr21/13971/2 "2014-11-21T08:42:18Z")

</div>

What are your firewall rules? (“type fw.hit”)

What interfaces is your firewall active on? (“nnn x firewall ?” where nnn is your interface and x is the instance)

What are your routes? (route print)

---

<div class="post-metadata">

**Author:** ![joe.vance](https://avatars.discourse-cdn.com/v4/letter/j/67e7ee/32.png) [@joe.vance](https://forums.digi.com/u/joe.vance)\
**Post date:** [November 21, 2014, 1:43pm UTC](https://forums.digi.com/t/why-do-pings-time-out-from-devices-connected-to-my-wr21/13971/3 "2014-11-21T13:43:33Z")

</div>

Current firewall rules:

#Allow any other outbound traffic and the replies back in  
pass out log break end inspect-state  
pass in break end proto icmp  
#Allow incoming IPSEC  
pass break end proto 50  
pass in break end proto udp from any to any port=ike  
pass in break end proto udp from any to any port=4500  
#Allow any traffic within an IPSEC tunnel in both directions  
pass break end oneroute any  
#Allow incoming SSH and SFTP  
pass in break end proto tcp from any to any port=22 flags S!A inspect-state  
#Allow incoming HTTPS  
#pass in break end proto tcp from any to any port=443 flags S!A inspect-state  
pass in break end proto tcp from any to any port=8443 flags S!A inspect-state  
pass in break end on ppp 1 from any to addr-ppp 1 port=http -\> to 192.168.1.100 port=http inspect-state  
pass in break end on ppp 1 from any to addr-ppp 1 port=443 -\> to 192.168.1.100 port=443 inspect-state  
#Block and log everything else including incoming telnet, http and FTP  
block log break end

The firewall is active on ppp 1 only.

routing table:

```
   Destination Gateway Metric Protocol Idx Interface Status

```

* * *

```
 166.xxx.xxx.xxx/29 166.xxx.xxx.xxx 1 Local - PPP 1 UP
 192.168.1.0/24 192.168.1.1 1 Local - ETH 0 UP

     0.0.0.0/0 166.xxx.xxx.xxx 2 Static 0 PPP 1 UP

```

---

<div class="post-metadata">

**Author:** ![joe.vance](https://avatars.discourse-cdn.com/v4/letter/j/67e7ee/32.png) [@joe.vance](https://forums.digi.com/u/joe.vance)\
**Post date:** [November 21, 2014, 1:43pm UTC](https://forums.digi.com/t/why-do-pings-time-out-from-devices-connected-to-my-wr21/13971/4 "2014-11-21T13:43:37Z")

</div>

Current firewall rules:

#Allow any other outbound traffic and the replies back in  
pass out log break end inspect-state  
pass in break end proto icmp  
#Allow incoming IPSEC  
pass break end proto 50  
pass in break end proto udp from any to any port=ike  
pass in break end proto udp from any to any port=4500  
#Allow any traffic within an IPSEC tunnel in both directions  
pass break end oneroute any  
#Allow incoming SSH and SFTP  
pass in break end proto tcp from any to any port=22 flags S!A inspect-state  
#Allow incoming HTTPS  
#pass in break end proto tcp from any to any port=443 flags S!A inspect-state  
pass in break end proto tcp from any to any port=8443 flags S!A inspect-state  
pass in break end on ppp 1 from any to addr-ppp 1 port=http -\> to 192.168.1.100 port=http inspect-state  
pass in break end on ppp 1 from any to addr-ppp 1 port=443 -\> to 192.168.1.100 port=443 inspect-state  
#Block and log everything else including incoming telnet, http and FTP  
block log break end

The firewall is active on ppp 1 only.

routing table:

Destination Gateway Metric Protocol Idx Interface Status  
166.xxx.xxx.xxx/29 166.xxx.xxx.xxx 1 Local - PPP 1 UP  
192.168.1.0/24 192.168.1.1 1 Local - ETH 0 UP

0.0.0.0/0 166.xxx.xxx.xxx 2 Static 0 PPP 1 UP

---

<div class="post-metadata">

**Author:** ![joe.vance](https://avatars.discourse-cdn.com/v4/letter/j/67e7ee/32.png) [@joe.vance](https://forums.digi.com/u/joe.vance)\
**Post date:** [November 21, 2014, 1:43pm UTC](https://forums.digi.com/t/why-do-pings-time-out-from-devices-connected-to-my-wr21/13971/5 "2014-11-21T13:43:48Z")

</div>

I think I’ve figured it out. I didn’t have NAT enabled on my PPP 1 interface.
