# \#rate

**URL:** https://forums.digi.com/tag/rate/446.md

[Latest](https://forums.digi.com/latest.md) · [Categories](https://forums.digi.com/categories.md) · [Tags](https://forums.digi.com/tags.md)

---

## [Can i increase RF data rate (Kbps)](https://forums.digi.com/t/can-i-increase-rf-data-rate-kbps/21690)

<div class="topic-metadata">

**Author:** [@HakanErsoy](https://forums.digi.com/u/HakanErsoy)\
**Replies:** 1\
**Last updated:** [August 24, 2020, 9:09am UTC](https://forums.digi.com/t/can-i-increase-rf-data-rate-kbps/21690 "2020-08-24T09:09:48Z")

</div>

i have XBee PRO S2C, i communicate both of , There is 50cm distance between the two but my RF data rate is 30 Kbps it should be 250 Kbps according to Datasheet. can i increase RF data rate if so how can i increase tha…

---

## [Firewall scripts ICMP echo](https://forums.digi.com/t/firewall-scripts-icmp-echo/19408)

<div class="topic-metadata">

**Author:** [@jserink](https://forums.digi.com/u/jserink)\
**Replies:** 1\
**Last updated:** [August 15, 2018, 3:54am UTC](https://forums.digi.com/t/firewall-scripts-icmp-echo/19408 "2018-08-15T03:54:42Z")

</div>

Hello: I would like to set a maximum number of ICMP echo replies per second so say 10 so as to prevent a ping flood attack. Cisco can do this so was wondering if this can be done as a Digi Transport firewall rule. Chee…

---

## [Baud rate adjusted now no connection to xbee 900hp possible](https://forums.digi.com/t/baud-rate-adjusted-now-no-connection-to-xbee-900hp-possible/17291)

<div class="topic-metadata">

**Author:** [@Stefan001](https://forums.digi.com/u/Stefan001)\
**Replies:** 2\
**Last updated:** [August 29, 2016, 8:06am UTC](https://forums.digi.com/t/baud-rate-adjusted-now-no-connection-to-xbee-900hp-possible/17291 "2016-08-29T08:06:10Z")

</div>

I have a XBEE XB 900 HP 10k RS 232 I adjusted the BD to 230400. Now i can not reconnect to the device. -\> port configuration is not valid. I tried to reset the Firmware but the Baud rate is 230400, again. What can i d…

---

## [Baud rate selection for S2C](https://forums.digi.com/t/baud-rate-selection-for-s2c/16855)

<div class="topic-metadata">

**Author:** [@gcelik123](https://forums.digi.com/u/gcelik123)\
**Replies:** 1\
**Last updated:** [May 31, 2016, 9:49pm UTC](https://forums.digi.com/t/baud-rate-selection-for-s2c/16855 "2016-05-31T21:49:09Z")

</div>

Hi, I am using S2C modules in my project. When I set two module as AT mode in XCTU, I get about 23 kbps throughput at 38400 Baud rate in throughput test. However, when I set baud rate greater than 38400 - 58400 or 11520…

---

## [Setting XBee S2 UART to 250kbps](https://forums.digi.com/t/setting-xbee-s2-uart-to-250kbps/15173)

<div class="topic-metadata">

**Author:** [@idrox](https://forums.digi.com/u/idrox)\
**Replies:** 1\
**Last updated:** [September 2, 2015, 1:54pm UTC](https://forums.digi.com/t/setting-xbee-s2-uart-to-250kbps/15173 "2015-09-02T13:54:37Z")

</div>

Is it possible to configure the XBee S2 UART at 250kbps? I could not find any specific documentation on the non-standard baud rates. Thanks.

---

## [Arduino to Arduino Wireless with voice module at Transmitter Arduino and motor on receiver Arduino](https://forums.digi.com/t/arduino-to-arduino-wireless-with-voice-module-at-transmitter-arduino-and-motor-on-receiver-arduino/14315)

<div class="topic-metadata">

**Author:** [@Muhammad\_Awais\_khan](https://forums.digi.com/u/Muhammad_Awais_khan)\
**Replies:** 2\
**Last updated:** [April 24, 2015, 8:02am UTC](https://forums.digi.com/t/arduino-to-arduino-wireless-with-voice-module-at-transmitter-arduino-and-motor-on-receiver-arduino/14315 "2015-04-24T08:02:57Z")

</div>

I am using two Xbees, I am using voice module elechouse v3 that operates on 115200 baud rate. I want voice module to process voice at transmission end and glow an led with it at receivers end. Problem is the baud rate …

---

## [Xbee 802.15.4 Transfer Rate and Sample Rate Capabilities](https://forums.digi.com/t/xbee-802-15-4-transfer-rate-and-sample-rate-capabilities/14206)

<div class="topic-metadata">

**Author:** [@ajoshua](https://forums.digi.com/u/ajoshua)\
**Replies:** 1\
**Last updated:** [January 26, 2015, 1:30pm UTC](https://forums.digi.com/t/xbee-802-15-4-transfer-rate-and-sample-rate-capabilities/14206 "2015-01-26T13:30:41Z")

</div>

I was reading that the Xbee has a sampling rate of 50 Hz. I was wondering if in AT mode I have to worry about aliasing. I don’t know too much about Xbee modules, but my main consider is just receiving data on one Xbee (S…

---

## [Xbee digimesh module is not supporting 115200 baud rate?](https://forums.digi.com/t/xbee-digimesh-module-is-not-supporting-115200-baud-rate/14134)

<div class="topic-metadata">

**Author:** [@Navas\_K\_K](https://forums.digi.com/u/Navas_K_K)\
**Replies:** 1\
**Last updated:** [January 6, 2015, 2:49pm UTC](https://forums.digi.com/t/xbee-digimesh-module-is-not-supporting-115200-baud-rate/14134 "2015-01-06T14:49:19Z")

</div>

For testing the data throughput of Xbee digimesh modules , i used the following setup. Configured two Xbee digimesh module with digimesh firmware with a baud rate of 57600. C program in linux to send data packet to one …

---

## [XBee Max Baud Rate Problems](https://forums.digi.com/t/xbee-max-baud-rate-problems/14119)

<div class="topic-metadata">

**Author:** [@caseyzahorik](https://forums.digi.com/u/caseyzahorik)\
**Replies:** 1\
**Last updated:** [December 30, 2014, 8:48am UTC](https://forums.digi.com/t/xbee-max-baud-rate-problems/14119 "2014-12-30T08:48:23Z")

</div>

I’m using XBee XB24-Z7SIT-004 and I’m having problems setting the baud rate to the advertised 250kbps using X-CTU. The max baud rate i can set in X-CTU is 115200. Additional information or screenshots can be provided if…

---

## [Baud rate error with Xbee PRO](https://forums.digi.com/t/baud-rate-error-with-xbee-pro/13390)

<div class="topic-metadata">

**Author:** [@jag](https://forums.digi.com/u/jag)\
**Replies:** 1\
**Last updated:** [August 1, 2014, 9:33am UTC](https://forums.digi.com/t/baud-rate-error-with-xbee-pro/13390 "2014-08-01T09:33:55Z")

</div>

I’m having trouble getting Xbee PRO to work reliably at 115200. The issue seems to be the baud rate error in the Xbee pro. My scope shows that the actual baud rate from Xbee pro UART is closer to 113000, which results …

---

## [Not receiving enough frames after I use XCTU to set IR on Pro s2b endpoint.](https://forums.digi.com/t/not-receiving-enough-frames-after-i-use-xctu-to-set-ir-on-pro-s2b-endpoint/13207)

<div class="topic-metadata">

**Author:** [@nomad\_bee](https://forums.digi.com/u/nomad_bee)\
**Replies:** 3\
**Last updated:** [July 1, 2014, 9:58am UTC](https://forums.digi.com/t/not-receiving-enough-frames-after-i-use-xctu-to-set-ir-on-pro-s2b-endpoint/13207 "2014-07-01T09:58:02Z")

</div>

Hi all, I am trying to transmit 3 channels of analog accelerometer data at 30 SPS and 57600 Baud. I have pin hibernate on the endpoint with the sleep pin tied low. But first of all, the behaviour of the IR parameter…

---

## [XBee stop to comunicate after baud rate change](https://forums.digi.com/t/xbee-stop-to-comunicate-after-baud-rate-change/11519)

<div class="topic-metadata">

**Author:** [@puffosauro](https://forums.digi.com/u/puffosauro)\
**Replies:** 1\
**Last updated:** [May 13, 2014, 11:59am UTC](https://forums.digi.com/t/xbee-stop-to-comunicate-after-baud-rate-change/11519 "2014-05-13T11:59:49Z")

</div>

I hope someone can help me. I’m using two XBee Series 2 with this configuration: ZNET 2.5 COORDINATOR API (1147) ZNET 2.5 ROUTER/END DEVICE AT (1247) The first XBee is connected to an Arduino board and I’m able to sw…

---

## [Can Digi Acceleport (RS422)support Custom Baud Rate Settings with Linux?](https://forums.digi.com/t/can-digi-acceleport-rs422-support-custom-baud-rate-settings-with-linux/12737)

<div class="topic-metadata">

**Author:** [@svishere](https://forums.digi.com/u/svishere)\
**Replies:** 1\
**Last updated:** [April 1, 2014, 9:15am UTC](https://forums.digi.com/t/can-digi-acceleport-rs422-support-custom-baud-rate-settings-with-linux/12737 "2014-04-01T09:15:25Z")

</div>
