# \#static **URL:** https://forums.digi.com/tag/static/1163.md [Latest](https://forums.digi.com/latest.md) · [Categories](https://forums.digi.com/categories.md) · [Tags](https://forums.digi.com/tags.md) --- ## [How to disable "IAM:AUTOIP IPv4 xxx on eth0:0" message?](https://forums.digi.com/t/how-to-disable-iam-autoip-ipv4-xxx-on-eth0-0-message/23016)
**Author:** [@ottelo](https://forums.digi.com/u/ottelo)\ **Replies:** 6\ **Last updated:** [September 23, 2022, 8:57am UTC](https://forums.digi.com/t/how-to-disable-iam-autoip-ipv4-xxx-on-eth0-0-message/23016 "2022-09-23T08:57:10Z")
I have a Digi ME 9210 with NET+OS configured with static IPv4 IP. If I boot up with serial cable connected, I see all boot infos and my printf messages from my firmware. But after the boot I get this annoying message “IA… --- ## [Static IP RCM 4300 cannot be reached from sub network](https://forums.digi.com/t/static-ip-rcm-4300-cannot-be-reached-from-sub-network/22885)
**Author:** [@Thomas\_A](https://forums.digi.com/u/Thomas_A)\ **Replies:** 4\ **Last updated:** [January 14, 2022, 8:36am UTC](https://forums.digi.com/t/static-ip-rcm-4300-cannot-be-reached-from-sub-network/22885 "2022-01-14T08:36:40Z")
Hi, I am using a RCM 4300 with dcrtcp.lib and http.lib. It is configured as a static IP 10.130.216.11 on a subnet, called “A”. From a computer on another subnet, called “B”, physically linked to “A” with the following … --- ## [PAT entry from Inside to outside](https://forums.digi.com/t/pat-entry-from-inside-to-outside/21974)
**Author:** [@jserink](https://forums.digi.com/u/jserink)\ **Replies:** 0\ **Last updated:** [November 6, 2020, 3:56am UTC](https://forums.digi.com/t/pat-entry-from-inside-to-outside/21974 "2020-11-06T03:56:38Z")
Hi Guys: We have a WR21 in port isolate mode. Eth1 is the Internal network and Eth0 is the Internet via an ISP fiber or ADSL router. We are using GPRS as backup. Eth0 is in DHCP mode so it picks up an ip address from t… --- ## [Can't get Rabbitcore module to connect to Device Cloud when set to static IP](https://forums.digi.com/t/cant-get-rabbitcore-module-to-connect-to-device-cloud-when-set-to-static-ip/20056)
**Author:** [@braves3131](https://forums.digi.com/u/braves3131)\ **Replies:** 1\ **Last updated:** [December 21, 2018, 7:13pm UTC](https://forums.digi.com/t/cant-get-rabbitcore-module-to-connect-to-device-cloud-when-set-to-static-ip/20056 "2018-12-21T19:13:29Z")
I have an RCM6760 which I need to be able to configure the ethernet port during runtime for DHCP or Static IP. In either mode I need to be able to connect the RCM with Device Cloud. The issue I am having is I can not get… --- ## [Saving static IP address on WR31.](https://forums.digi.com/t/saving-static-ip-address-on-wr31/19779)
**Author:** [@pabeaver](https://forums.digi.com/u/pabeaver)\ **Replies:** 1\ **Last updated:** [August 15, 2018, 3:21am UTC](https://forums.digi.com/t/saving-static-ip-address-on-wr31/19779 "2018-08-15T03:21:52Z")
When I enter a static IP address in the configuration section using the web interface it is not saved. I need to reset the router to default to even see the web interface again. How can I do this correctly? Thanks. --- ## [Why is my XBee receiving so many bogus digital I/O signal edges ?](https://forums.digi.com/t/why-is-my-xbee-receiving-so-many-bogus-digital-i-o-signal-edges/12612)
**Author:** [@luotzi](https://forums.digi.com/u/luotzi)\ **Replies:** 1\ **Last updated:** [May 7, 2014, 11:02am UTC](https://forums.digi.com/t/why-is-my-xbee-receiving-so-many-bogus-digital-i-o-signal-edges/12612 "2014-05-07T11:02:34Z")
I have a remote switch operating as a “sensor” over a pair of XBee Pro:s. The remote end has a pull-down resistor, so the input is not “floating” midway. Otherwise it works as expected, but I receive a lot of transient s…