Error 4 in libgtk-3 - XCTU

XBee & XBee Gateway XBee Programamble (S2C & 900 HP)
1

Hello,

I get this error after a while of use in linux and XCTU is closed:

42061.840883] usb 2-1.2: FTDI USB Serial Device converter now attached to ttyUSB0
[42104.051968] usb 2-1.2: USB disconnect, device number 70
[42104.052215] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[42104.052245] ftdi_sio 2-1.2:1.0: device disconnected
[42114.749977] usb 2-1.2: new full-speed USB device number 71 using ehci-pci
[42114.850390] usb 2-1.2: New USB device found, idVendor=0403, idProduct=6015
[42114.850395] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[42114.850399] usb 2-1.2: Product: FT231X USB UART
[42114.850402] usb 2-1.2: Manufacturer: FTDI
[42114.850405] usb 2-1.2: SerialNumber: DA01M9KO
[42114.853566] ftdi_sio 2-1.2:1.0: FTDI USB Serial Device converter detected
[42114.853635] usb 2-1.2: Detected FT-X
[42114.854208] usb 2-1.2: FTDI USB Serial Device converter now attached to ttyUSB0
[43975.372803] gedit[23601]: segfault at 400000000 ip 00007fbcf38f9aac sp 00007ffd5e7c2da0 error 4 in libgtk-3.so.0.1400.13[7fbcf3858000+6b1000]
Search Thread for /dev/ttyUSB0 STARTED.
Testing /dev/ttyUSB0 - 9600/8/N/1/N
*** PORT /dev/ttyUSB0 CLOSED ***
Search Thread for /dev/ttyUSB0 STOPPED.
Search Thread for /dev/ttyUSB0 STARTED.
Testing /dev/ttyUSB0 - 9600/8/N/1/N
*** PORT /dev/ttyUSB0 CLOSED ***
--------- Local XBeeDevice ---------
Interface:        /dev/ttyUSB0 - 9600/8/N/1/N
Working mode:     API 2
Protocol:         Point-to-multipoint
MAC Address:      0013A20040A292C0
16-bit address:   FFFE
Node Identifier:   
Device type:      Coordinator
Hardware version: 1D
Firmware version: 1061

Search Thread for /dev/ttyUSB0 STOPPED.

Do I need to upgrade or install other library?

Best regards

2

What module and board are you working with? What version of XCTU are you working with?

3

Sparkfun Usb Explorer with XBee 868 Pro and XCTU
Version: 6.2.0
Build ID: 20150508-6

In Ubuntu 15.04 Vivid Vervet x86_64 with Oracle Java 1.8.0_60

Best regards

4

I don’t think that the Exporere board from Spark fun can provide the current requirments of the XBee PRO 868 module hence the issues you are seeing. I would suggest contact Spark Fun and first seeing if there is an updated driver you should be using and second if that board can support and proivide the current that the 868 PRO module wants.

5

Don’t worry.

I take about two months without this error. If reappears again, I try to contact with Sparkfun.

I use this reference WRL-11812 , V21

Only with XCTU, for microcontroller or microprocessor I use UART and work fine.

Thank you and regards.